Blue decorative line graphic used in ProDetec branding

Workplace Dust Monitoring Solutions for Industrial Health, Safety, and Compliance

ProDetec supplies workplace dust monitoring solutions for Australia’s mining, grain handling, flour milling, timber, chemical and bulk powder handling facilities, providing continuous, real-time measurement of airborne particulate concentrations. This protects worker health, helps meet regulatory exposure obligations and reduces the risk of dust explosion events where combustible dust accumulates. Without reliable workplace dust monitoring equipment, elevated dust levels can go undetected until health impacts, housekeeping failures or compliance breaches force you to act.

With over 22 years of experience and local engineering support across Australia, ProDetec supplies, commissions, and supports the full Sintrol workplace dust monitor range for facilities of all sizes.

ProDetec’s primary workplace dust monitor is the Sintrol DumoPro, a continuous 24/7 ambient air dust monitor using Sintrol’s patented Inductive Electrification technology to detect total suspended particles (TSP) with sensitivity down to 0.3 microns, Auto-Setup commissioning, and an IP66-rated enclosure built for demanding industrial environments. The ATEX and IECEx certified DumoPro Ex variant extends full workplace dust monitoring equipment capability into hazardous dust areas classified as Zones 20, 21, and 22.

Australia's mining, grain handling dust monitoring
Blue decorative line graphic used in ProDetec branding

Range of Workplace Dust Monitoring Solutions

DumoPro | Ambient Air Dust Monitor

DumoPro | Ambient Air Dust Monitor

The Sintrol DumoPro is a continuous ambient air dust monitor engineered for real-time, 24/7 monitoring of total suspended particles in industrial workplaces. Using low-maintenance inductive electrification technology, the DumoPro provides early warning of dust events, supports worker protection, and helps mitigate the risk of dust explosions. Features include Auto-Setup commissioning, automatic Zero and Span checks, and an on-board display. The ATEX and IECEx certified DumoPro Ex variant extends the same performance to hazardous dust areas (Zones 20, 21, 22) across mining, grain, timber, and powder handling industries.

Read more
Sintrol S101 / S103 Filter Monitor | Broken Bag Detector

Sintrol S101 / S103 Filter Monitor | Broken Bag Detector

The Sintrol S101 / S103 filter monitor is a fast-response dust detector engineered to identify broken bags and filter leaks in small duct systems under 80 cm. Based on proven inductive electrification technology, it detects any particulates in the airflow and responds rapidly to dust breakthrough, helping minimise product loss and protect downstream equipment.

The S101 features two adjustable solid-state alarm relays, while the S103 adds an active isolated 4–20 mA output for continuous trend monitoring. Both variants are ATEX and IECEx certified, with rugged IP66 construction, visible status LEDs, self-teaching Auto Setup, and selectable FAST, MEDIUM, and SLOW response modes.

Read more
S201 DustGuard | Filter Leak Detector

S201 DustGuard | Filter Leak Detector

The Sintrol S201 is a real-time dust monitor and broken bag detector engineered to identify filter leaks, bag house failures, and abnormal dust levels in industrial duct systems. Suitable for ducts up to 7000 mm, the S201 uses inductive electrification technology to deliver accurate measurements from as low as 0.01 mg/m³ across a wide linear range.

Two independent SPDT relays and RS-485 Modbus RTU communication enable seamless integration with plant control systems. The ATEX, IECEx, and HazLoc certified S201 Ex variant extends performance to hazardous dust areas (Zones 20, 21, 22) across mining, cement, grain, timber, and process industries.

Read more
S201 DustGuard | Filter Leak Detector

S203 Trend Monitor | Continuous Dust Trend Analysis

Continuous trend monitor that gives plant operators to see the performance of the filtration systems and ducts over a period of time. Perfect for installation after any filtration system or in common line channels leading into the emissions points of a plant.

State of the art Inductive Electrification principle minimises the need for maintenance on the dust monitor and provides an accurate trend for end users. 4-20mA output combined with an easy to use auto-setup feature that takes less than 30 minutes from installation makes the device both convenient and reliable.

Read more
S303 Process Dust Monitor

S303 Process Dust Monitor

Continuous trend monitor that gives plant operators to see the performance of the filtration systems and ducts over a period of time. Perfect for installation after any filtration system or in common line channels leading into the emissions points of a plant.

State of the art Inductive Electrification principle minimises the need for maintenance on the dust monitor and provides an accurate trend for end users. 4-20mA output combined with an easy to use auto-setup feature that takes less than 30 minutes from installation makes the device both convenient and reliable.

Read more
S303 Process Dust Monitor

S304 Emissions Monitor

For applications requiring absolute value measurements of dust concentrations, the S304 can be calibrated to give the user a mg/m3 output. Once calibrated, this dust monitor helps plant operators know exactly how much dust is passing through the stack or outlet duct of their plant.

The S304 is additionally equipped with a 4-20 mA signal and two independent alarm relays that can be used to further optimised process conditions in the plant.

Utilising our unique Inductive Electrification principle, the S304 brings the reliability the government requires and combines it with the convenience plant operators expect from a particulate measurement device. With minimal maintenance required, this is an optimal solution for plant operators needing to measure stack dust emissions for government control.

Read more
S305QAL Dust Monitor

S305QAL Dust Monitor

Sintrol S305QAL Dust Monitor is EN15267-3 QAL1 certified particulate matter stack monitor for official emissions measurements. The S305QAL dust monitor meets the highest European standards as defined in EN14181. The S305QAL is approved for and is suitable for use on waste incineration and combustion plant applications. The S305QAL comes with many key features making it a very reliable, low maintenance, sensitive and robust solution for stack particulate matter measurements.

Read more